Canon EF 40mm f/2.8 STM

Canon EF 40mm f/2.8 STM ръководство на потребителя

(1)
  • Thank you for purchasing a Canon product.
    EF40mm f/2.8 STM is a compact, lightweight, low-profile high quality standard
    single focal point lens.
    “STM” stands for Stepping Motor.
    Safety Precautions
    Do not look at the sun or a bright light source through the lens or
    camera. Doing so could result in loss of vision.
    Looking at the sun directly through the lens is especially hazardous.
    Whether it is attached to the camera or not, do not leave the lens under
    the sun without the lens cap attached.
    This is to prevent the lens from
    concentrating the sun’s rays, which could cause a fire.
    Handling Cautions
    If the lens is taken from a cold environment into a warm one,
    condensation may develop on the lens surface and internal parts.
    To
    prevent condensation in this case, first put the lens into an airtight plastic
    bag before taking it from a cold to warm environment. Then take out the lens
    after it has warmed gradually. Do the same when taking the lens from a warm
    environment into a cold one.
    Do not leave the lens in excessive heat such as in a car in direct sunlight.
    High temperatures can cause the lens to malfunction.
    Cautions during shooting
    This lens uses a stepping motor to drive the focusing lens (the lens that has
    the job of focusing the shot).
    1. Cautions when the power is off
    Since the motor does not operate when the camera is off or has been
    turned by the auto power-off function, take note of the following points.
    s4HEFOCUSCANNOTBEADJUSTEDINMANUALFOCUSMODE
    2. Cautions when the lens is in sleep mode
    This lens has a sleep mode separate from the camera auto power-off
    function for saving power when the lens has not been operated for a period
    of time.
    Since the motor does not operate when the lens is in sleep mode, even if
    the camera is turned on, take note of the following points.
    s4HEFOCUSCANNOTBEADJUSTEDINMANUALFOCUSMODE
    s4ORECOVERTHELENSFROMSLEEPMODEPRESSTHESHUTTERBUTTONHALFWAY
    To shoot with this lens attached on an EOS-1D Mark IV, update the EOS-
    1D Mark IV firmware to version 1.1.1 or later. Updating to this firmware will
    optimize exposure accuracy.
    When using an EOS film camera, the action of the focus may slow down if
    the battery is low on power or when the ambient temperature is low.
    About the AF frame selection
    High accuracy cross (+) detection can be used in the center AF frame and
    horizontal line detection can be used in the frames other than the center AF
    frame for the following cameras.
    EOS-1Ds Mark III, EOS-1Ds Mark II, EOS-1Ds, EOS-1D Mark IV,
    EOS-1D Mark III, EOS-1D Mark II N, EOS-1D Mark II, EOS-1D, EOS-1V,
    EOS-3
    Conventions used in this instruction
    Warning to prevent lens or camera malfunction or damage.
    Supplementary notes on using the lens and taking pictures.
    1. Mounting and Detaching the Lens
    See your camera’s instructions for details on mounting and detaching the
    lens.
    After detaching the lens, place the lens with the rear end up to prevent
    the lens surface and contacts from getting scratched.
    If the contacts get soiled, scratched, or have fingerprints on them,
    corrosion or faulty connections can result. The camera and lens may not
    operate properly.
    If the contacts get soiled or have fingerprints on them, clean them with a
    soft cloth.
    If you remove the lens, cover it with the dust cap. To attach it properly,
    align the lens mount index and the
    index of the dust cap, and turn
    clockwise
    . To remove it, reverse the order.
    2. Setting the Focus Mode
    To shoot in autofocus (AF) mode, set the focus mode switch to AF
    .
    To shoot in manual focus (MF) mode, set the focus mode switch to MF, and turn
    the focusing ring to set the focus
    .
    When the camera AF mode is ONE SHOT AF, focus manually by pressing
    the shutter button halfway and turning the focusing ring. (Full-time manual
    focus)
    When turning the focusing ring suddenly, the focus adjustment may be
    delayed.
    The focus cannot be adjusted in MF mode while the camera is off.
    Do not touch the front rotating parts of the lens while autofocus is active.
    Nomenclature
    Focus mode switch
    Focusing ring
    Lens mount index
    Contacts
    EF Lenses
    EF40mm f/2.8 STM
    Instructions
Canon EF 40mm f/2.8 STM

Имате ли въпрос относно Canon EF 40mm f/2.8 STM?

Брой въпроси: 0

Задайте въпроса, който имате за Canon EF 40mm f/2.8 STM тук направо на други собственици на продукта. Дайте ясно и изчерпателно описание на проблема и Вашия въпрос. Колкото по–добре опишете проблема си и зададете въпроса си, толкова по–лесно другите собственици на Canon EF 40mm f/2.8 STM ще могат да Ви дадат добър отговор.

Тук вижте безплотното ръководство за Canon EF 40mm f/2.8 STM. Прочетохте ли ръководството, но отговаря ли то на Вашия въпрос? Тогава задайте въпроса си на тази страница на други собственици на Canon EF 40mm f/2.8 STM. Задайте въпроса си тук

Спецификации на продукта

Марка Canon
Модел EF 40mm f/2.8 STM
Продукт Обектив
EAN 4960999845715, 5053959359724, 5053973184579, 5056066707358, 5554442238798, 8030207007863
Език Английски, Френски
Вид файл PDF
Система на обектива
Тип обектив Стандартни лещи
Компонент за SLR
Структура на обектива 6/4
Фиксирано фокусно разстояние 40мм
Брой елемети изграждащи диафрагмата 7
Най-близко фокусиране 0.3м
Стабилизатор на изображението
Зрителен ъгъл (по хоризонтала) 49°
Зрителен ъгъл (по вертикала) 34°
Диагонален зрителен ъгъл (мин.) 57°
Интерфейс за монтиране на обектива Ca✗n EF
Максимален номер на блендата 22
Диагонален зрителен ъгъл (макс.) 57°
Тегло и размери
Диаметър 68.2мм
Дължина 22.8мм
Размер на филтъра 52мм
Тегло 130г
Други характеристики
Увеличение 0.18x
Производителност
AF задвижващ механизъм STM
Съвместимост EOS
Съвместимост с други марки Ca✗n
Автофокус
Дизайн
Цвят на продукта Черен

Свързани продукти

Обектив Canon