Canon EF-M22MM F2 STM

Canon EF-M22MM F2 STM ръководство на потребителя

(1)
  • ENG-1
    ENG
    EF-M LENS Instructions
    EF-M22mm f/2 STM
    Nomenclature
    Focusing ring
    Hood/Filter Mounting Thread
    Lens mount index
    Contacts
    Thank you for purchasing a Canon product.
    The Canon EF-M22mm f/2 STM lens is a small fixed
    focus length lens developed for interchangeable-lens
    digital cameras compatible with EF-M lenses*.
    * Only the following cameras are compatible with
    EF-M lenses (as of July 2012):
    EOS M
    "STM" stands for stepping motor.
    Safety Precautions
    Do not look at the sun or a bright light source
    through the lens. Doing so could result in vision
    loss or blindness.
    Whether it is attached to the camera or not, do
    not leave the lens under the sun without the
    lens cap attached. This is to prevent the lens
    from concentrating the sun’s rays, which could
    cause a fire.
    Handling Cautions
    If the lens is taken from a cold environment
    into a warm one, condensation may develop
    on the lens surface and internal parts. To
    prevent condensation in this case, first put the
    lens into an airtight plastic bag before taking it
    from a cold to warm environment. Then take
    out the lens after it has warmed gradually. Do
    the same when taking the lens from a warm
    environment into a cold one.
    Do not leave the lens in excessive heat such as
    in a car in direct sunlight. High temperatures
    can cause the lens to malfunction.
    Please also refer to the handling cautions found
    in your camera’s instructions.
    Conventions used in this instruction
    Warning to prevent lens or camera
    malfunction or damage.
    Supplementary notes on using the lens and
    taking pictures.
    This device complies with Part 15 of the FCC Rules.
    Operation is subject to the following two conditions: (1)
    This device may not cause harmful interference, and
    (2) this device must accept any interference received,
    including interference that may cause undesired
    operation.
    Do not make any changes or modifications to
    the equipment unless otherwise specified in the
    instructions. If such changes or modifications should
    be made, you could be required to stop operation of
    the equipment.
    This equipment has been tested and found to comply
    with the limits for a class B digital device, pursuant
    to part 15 of the FCC Rules. These limits are
    designed to provide reasonable protection against
    harmful interference in a residential installation. This
    equipment generates, uses and can radiate radio
    frequency energy and, if not installed and used in
    accordance with the instructions, may cause harmful
    interference to radio communications.
    However, there is no guarantee that interference will
    not occur in a particular installation. If this equipment
    does cause harmful interference to radio or television
    reception, which can be determined by turning the
    equipment off and on, the user is encouraged to
    try to correct the interference by one or more of the
    following measures:
    Reorient or relocate the receiving antenna.
    Increase the separation between the equipment
    and receiver.
    Consult the dealer or an experienced radio/TV
    technician for help.
    This Class B digital apparatus complies with
    Canadian ICES-003.
    1. Mounting and Detaching the Lens
    Please mount and detach the lens only with the
    camera turned OFF.
    See your camera’s instructions for details on
    mounting and detaching the lens.
    After detaching the lens, place the lens with
    the rear end up to prevent the lens surface and
    contacts from getting scratched. (fig.)
    If the contacts get soiled, scratched, or have
    fingerprints on them, corrosion or faulty
    connections can result. The camera and lens
    may not operate properly.
    If the contacts get soiled or have fingerprints on
    them, clean them with a soft cloth.
    If you remove the lens, cover it with the dust
    cap. To attach it properly, align the lens mount
    index and the
    index of the dust cap as shown
    in the diagram, and turn clockwise. (fig.) To
    remove it, reverse the order.
    2. Manual Focus
    When the camera’s focus mode is set to [MF], focus
    manually by turning the focusing ring (fig.).
    Quickly rotating the focusing ring may result in
    delayed focus.
    Focus mode is set using the camera. Please
    refer to the camera’s instructions.
    After autofocusing in [AF+MF] mode, focus
    manually by pressing the shutter button halfway
    and turning the focusing ring (full-time manual
    focusing).
    CT1-8584-000
    COPY
Canon EF-M22MM F2 STM

Имате ли въпрос относно Canon EF-M22MM F2 STM?

Брой въпроси: 0

Задайте въпроса, който имате за Canon EF-M22MM F2 STM тук направо на други собственици на продукта. Дайте ясно и изчерпателно описание на проблема и Вашия въпрос. Колкото по–добре опишете проблема си и зададете въпроса си, толкова по–лесно другите собственици на Canon EF-M22MM F2 STM ще могат да Ви дадат добър отговор.

Тук вижте безплотното ръководство за Canon EF-M22MM F2 STM. Прочетохте ли ръководството, но отговаря ли то на Вашия въпрос? Тогава задайте въпроса си на тази страница на други собственици на Canon EF-M22MM F2 STM. Задайте въпроса си тук