Honeywell RTH230B ръководство на потребителя

Honeywell RTH230B
9.2 · 2
PDF ръководство на потребителя
 · 4 страници
Английски
ръководство на потребителяHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Тук вижте безплотното ръководство за Honeywell RTH230B. Прочетохте ли ръководството, но отговаря ли то на Вашия въпрос? Тогава задайте въпроса си на тази страница на други собственици на Honeywell RTH230B. Задайте въпроса си тук

Имате ли въпрос относно Honeywell RTH230B?

Въпросът Ви за Honeywell ли се отнася и няма ли отговор на него в ръководството?

  • Получавайте актуализации за решения
  • Получавайте отговори на Вашия въпрос

Въпрос и отговор

Брой въпроси: 0

Термостатът Honeywell RTH230B е удобен, лесен за използване и е направен да контролира температурата на вашия дом. Той има емблематичен дисплей за лесна видимост и разполага с цифров контрол на температурата. Можете да го програмирате в два режима – за работа и за отдих – възможността да забавите увеличението на топлината през седмицата и да зададете това, което ви е нужно, за да създадете оптимално комфортно усещане. Термостатът може да се използва за 24V системи, както и за бойлери и термопомпи. Той има опция да бъде заключен, за да спре деца или други хора да го променят случайно или небрежно, а неговият механизъм за запазване на настройките ще спаси всички настройки дори при изключване на захранването. Термостатът Honeywell RTH230B е изработен от висококачествени материали, за да се гарантира неговата дълготрайност и е създаден да удовлетвори всяка нужда за контрол на температурата.

Общи
МаркаHoneywell
МоделRTH230B
Продукттермостати
ЕзикАнглийски
Вид файлРъководство за употреба (PDF)

Не можете да намерите отговора на въпроса си в ръководството? Може да намерите отговора на въпроса си в често задаваните въпроси относно Honeywell RTH230B по-долу.

Къде е най-доброто място за поставяне на термостата?

Най-доброто място за термостата е стаята, в която прекарвате най-много време, в много случаи това е холът или кухнята. Поставете термостата на около един и половина метра над пода, не на слънце и не на външна стена.

Какво е мъртъв обхват на термостата?

Ако Вашият термостат има мъртъв обхват, инсталация Ви е в състояние все едно в покой. Термостатът се включва само когато например разликата се отклонява повече от 2˚C от зададената стайна температура.

Каква е идеалната стайна температура?

Повечето хора смятат, че идеалната стайна температура е между 19 и 22 градуса по Целзий.

Налично ли е ръководството на Honeywell RTH230B на български?

За съжаление не разполагаме с ръководството за Honeywell RTH230B на български. Това ръководство е налично на Английски.

Не можете ли да откриете въпроса си? Задайте въпроса си тук

Няма резултати