Philips Norelco Multigroom 7100 QG3384

Philips Norelco Multigroom 7100 QG3384 ръководство на потребителя

(1)
  • Shaving With Mini Foil Shaver
    Use the narrow mini shaver to shave along con-
    toured edges to remove any stubble while creating
    a smooth, well-defined beard line.
    w Before using the mini shaver, always check it
    for wear and damage. If the mini shaver shows
    signs of wear or damage, do not use it as injury
    may occur. Do not use the mini shaver until it
    has been replaced.
    1 Pre-trim the contours desired with the
    trimmer or precision trimmer without a
    comb attachment.
    2 Put the mini shaver on the Groomer handle.
    3 Gently press the mini shaver onto the skin
    and shave along contoured edges to remove
    any stubble. Do not press too hard (fig. 22).
    Grooming Nose/Ear Hair
    1 Be certain the Groomer is in the OFF
    position.
    2 Remove the trimmer by turning counter-
    clockwise and pulling it off the Groomer
    handle.
    3 Put the nose/ear hair trimmer on the
    Groomer handle (1) and turn clockwise (2)
    (fig. 23).
    Trimming Nose Hair
    w Make sure nasal passages are clean.
    1 Put the nose/ear hair trimmer on the
    Groomer handle (1) and turn clockwise (2)
    (fig. 23).
    2 Turn the Groomer ON and insert the tip
    of the attachment into one nostril (fig. 24).
    CAUTION: Do Not insert the tip more
    than 3/16 in./5mm into your nostril.
    3 Slowly move the tip in and out while
    turning it around at the same time in order
    to remove unwanted hair. For best results,
    make sure the side of the tip is firm against
    skin. This will reduce the tickling effect that
    can occur during trimming of nose hair.
    4 Turn off Groomer. Rinse attachment clean
    after each use.
    Trimming Ear Hair
    w Clean outer area of ear and ear canal. Make
    sure it is free of wax.
    w Nose/ear hair trimmer should be on the
    Groomer.
    1 Turn the Groomer ON and move the tip
    softly around the edge of ear to remove hairs
    extending beyond the outer ear (fig. 25).
    2 Carefully insert the tip into outer ear canal
    (fig. 26).
    CAUTION: Do not insert the tip further
    than 3/16 in./5mm into the ear as this
    could cause damage to the eardrum.
    3 Turn off Groomer. Rinse attachment clean
    after each use.
    Cleaning
    w Clean the attachments after each use.
    w Always switch Groomer OFF, unplug
    and remove power supply cord from
    Groomer before cleaning.
    w Do not use compressed air, abrasive cleaning
    agents, scourers or liquids such as alcohol,
    benzene, bleach or acetone to clean the
    Groomer and attachments.
    w Never clean, replace or remove Groomer
    attachments with motor ON.
    w Do not apply pressure to cutters.
    w Do not touch cutters with hard objects as this
    may damage them.
    During Use:
    w If cut hairs have accumulated in the comb
    area, remove hairs by shaking, blowing or using
    cleaning brush provided. Remember to adjust
    the trimming length back to your selected set-
    ting when you replace the comb on Groomer.
    After Each Use:
    1 Make sure the Groomer is switched OFF
    and disconnected from the electrical outlet.
    2 Remove any comb or attachment.
    3 Blow and/or shake out any hair that may
    have accumulated in the comb or attachment.
    2 To contour the hairline around the ears,
    comb the hair ends over the ears.
    3 Tilt the Groomer in such a way that only
    one edge of the cutter blades touches the
    hair ends when you shape the contours
    around the ears (fig. 16).
    Be careful not to trim too much. The hairline
    should be close to the ear.
    4 To contour the nape of the neck or
    sideburns, turn the Groomer and make
    downward strokes (fig. 17).
    5 Move the Groomer slowly and smoothly
    following the natural hairline.
    Trimming your Beard & Moustache
    with Beard & Moustache Comb
    1 Put the trimmer on Groomer handle (1) and
    turn clockwise (2) (fig. 2).
    2 Slide the beard & moustache comb into
    the guiding grooves on both sides of the
    handle (fig. 18)
    .
    3 Press the Hair Length Setting Selector (1)
    and slide the comb to the desired setting (2)
    (fig. 19).
    The beard and moustache comb cuts hair to a
    length of 3/64-23/32in / 1-18mm.
    w If you are trimming for the first time, start
    by using the comb at the maximum trimming
    length setting (23/32 in/18mm) to prevent
    accidentally trimming hairs too short. As you
    become familiar with the settings, adjust Hair
    Length Setting Selector to desired trimming
    length. Selector will “click” into position at each
    setting.
    4 Turn the Groomer ON (fig. 5).
    5 To trim in the most effective way, move
    the Groomer against the direction of hair
    growth. Make sure the surface of the comb
    always stays in contact with the skin.
    NOTE: Since all hairs do not grow in the same
    direction, you may want to try different trimming
    positions (i.e., upwards, downwards, or across).
    Practice is best for optimum results.
    wIf a lot of hair has accumulated in the comb,
    remove the comb and blow and/or shake the
    hair out of the comb. You can also use the
    cleaning brush provided to remove
    hair from the comb area.
    w REMEMBER: You must reset the hair length
    selector back to your desired setting every time
    you replace the comb on the appliance.
    wThe remaining hair length corresponds with
    the smallest distance between the cutting
    blade and the spot where the comb is in contact
    with the skin.
    Beard Trimming Without
    Beard & Moustache Comb
    Remove comb if you are:
    w Defining hair lines
    w Trimming nape of neck
    w Removing single, unwanted hairs
    1 Be certain the Groomer is in the OFF
    position.
    2 Remove the comb by pressing the Hair
    Length Setting Selector (1) and slide the
    comb upwards (2). Pull comb off Groomer .
    3 Turn the Groomer ON (fig. 5).
    4 Make well-controlled movements. Touch the
    hair/skin lightly with the Groomer.
    Styling/Contouring with Precision
    Trimmer
    w Use the precision trimmer to cut shapes in
    beard hair or scalp hair.
    w Be careful when using the precision trimmer as
    it removes every hair it touches.
    1 Put the precision trimmer on the Groomer
    handle (1) and turn clockwise (2) (fig. 20).
    2 Make careful and controlled movements with
    the precision trimmer.
    3 For best results, move the precision trimmer
    against the direction of hair growth making
    sure it is in full contact with the skin (fig. 21).
    TIP: For the perfect finish, use the mini foil shaver
    to make edges and lines of your beard style even
    smoother (fig. 22).
    w Make sure the shaving foil is in complete
    contact with your skin for the closest shave
    and minimum foil wear.
    w Pressing too hard may cause skin irritation.
    w Practice is best for optimum results.
    1 Put the Bodygroom Shaver on the Groomer
    handle (1) and turn clockwise (2) (fig. 7).
    2 Turn the Groomer ON (fig. 5).
    3 Stretch your skin taut with your free hand
    and gently press Groomer to skin and move
    it slowly and smoothly, making sure the
    shaving foil is in full contact with the skin
    (fig. 8). Do not press too hard. Too much
    pressure can distort the foil and cause skin
    irritation.
    TIP: Stretching your skin can help hairs stand upright
    and minimize the chance of skin irritation.
    4 Always move the Groomer against the
    direction of hair growth (fig. 9).
    5 Turn OFF Groomer (fig. 5). Clean the
    body shaver after each use.
    Hair Clipping
    wMake sure that the appliance is fully charged
    before you start clipping hair.
    w Before you start clipping, make sure that the
    head of the person whose hair you are cutting
    is at the same level as your chest so that all
    parts of his/her head are clearly visible and
    within easy reach.
    w Make sure the hair is clean and dry.
    w Before you begin, comb the hair in the direction
    of growth (fig. 10).
    w To achieve optimal clipping results, always move
    the appliance slowly through the hair against
    the direction of hair growth.
    Clipping with hair clipping comb
    1 Put the trimmer on Groomer handle (1) and
    turn clockwise (2) (fig. 2).
    2 Slide the hair clipping comb into the guiding
    grooves on both sides of Groomer handle
    (fig. 11).
    3 Press the Hair Length Setting Selector (1)
    and slide the comb to the desired setting (2)
    (fig. 12).
    The hair clipping comb cuts hair to a length of 1/8
    in - 25/32 in / 3-20mm.
    4 The setting selected is shown on the back
    of the Groomer.
    When you are clipping for the first time, start
    at the maximum clipping length setting (25/32
    in/20mm) to familiarize yourself with the appliance
    and prevent accidentally trimming hairs too
    short. As you become familiar with the settings,
    adjust the Hair Length Setting Selector to desired
    trimming length. Selector will ‘click’ into position at
    each setting.
    5 Turn the Groomer ON (fig. 5).
    6 Make sure that the flat part of the comb is
    always in full contact with the scalp to obtain
    an even result (fig. 13).
    7 Move the appliance slowly over the crown
    from different directions to achieve an even
    result (fig. 14).
    8 Always move the appliance against the
    direction of hair growth.
    9 Make overlapping passes over the head to
    ensure that all hair that should be cut has
    been cut.
    10 Turn the Groomer off and remove the hair
    clipping comb often to blow and/or shake
    out hair that has accumulated.
    w REMEMBER: You must reset the hair length
    selector back to your desired setting every
    time you replace the hair clipping comb on the
    appliance.
    TIP: Write down the settings you have used to create
    a certain hairstyle as a reminder for future clipping
    sessions.
    Contouring without the hair clipping
    comb
    w Use the Groomer without a comb to clip hair
    very close to the skin (3/64in./1mm) or to
    contour the neckline and area around the ears.
    1 Remove the hair comb by pressing the Hair
    Length Setting Selector (1) and slide the
    comb upwards (2). Pull comb off Groomer
    (fig. 15).
    Be careful when you are clipping without a comb
    attachment as when the Clipper is turned on it
    will remove every hair it touches.
    IMPORTANT
    SAFETY
    INSTRUCTIONS
    When using an electric appliance, basic safety
    precautions should always be followed, including
    the following:
    Read all instructions before using this
    appliance.
    DANGER
    To reduce the risk of electric shock:
    1. Do not reach for a corded groomer that has
    fallen into water. Unplug immediately.
    2. Power plug and the accessories connected
    to it are not for immersion or for use in
    shower.
    3. Do not use an extension cord with this
    appliance.
    4. Always unplug the groomer from the
    electrical outlet immediately after use, except
    when groomer is (re)charging.
    5. Unplug and remove power supply cord from
    groomer before cleaning.
    6. The batteries used in this device may present
    a fire or chemical burn hazard if mistreated.
    Do not disassemble, heat above 100°C
    (212°F) or incinerate.
    WARNING
    To reduce the risk of burns, fire, electric
    shock or injury to persons:
    1. Close supervision is necessary when
    this appliance is used by, on, or near children
    or invalids.
    2. Use this groomer for its intended household
    use as described in this manual. Do not use
    attachments not recommended by Philips
    Electronics North America Corporation.
    3. Never operate this groomer if it has a
    damaged cord or plug, if it is not working
    properly, if it has been dropped, damaged,
    or dropped into water while plugged in. For
    assistance call 1-800-243-3050.
    4. Keep the groomer, cord, charging plug and
    any attachments away from heated
    surfaces.
    5. Never drop or insert any object into any
    opening.
    6. Do not operate, charge, clean or plug in
    groomer outdoors or where aerosol (spray)
    products are being used or where oxygen is
    being administered.
    7. Always check foils, cutters, cutting unit,
    combs and trimmers before using the groom-
    er. Do not use the groomer if foils, cutters,
    cutting unit, combs or trimmers are damaged,
    as injury may occur.
    8. Always attach plug to groomer first, then
    to outlet. To disconnect, turn groomer “OFF”,
    then remove plug from outlet.
    9. To prevent possible damage to the cord, do
    not wrap cord around the groomer.
    10. Never put groomer in direct sunlight or
    store at a temperature above 140°F.
    11. This groomer is for use on human hair only.
    Do not use this groomer for any other
    purpose.
    12. Groomer is water-safe and can be rinsed
    under running tap water or used in the
    shower. Do not submerge groomer in water.
    13. Only use the power plug and other
    accessories supplied with the appliance.
    SAVE THESE
    INSTRUCTIONS
    IMPORTANT: The power plug contains
    a transformer. Do not cut off the power
    plug to replace it with another plug as this
    will cause a hazardous condition.
    Turbo Power
    w Simply press the Turbo Button for a turbo
    power boost for fast results and the Turbo
    indicator will light up blue. The memory
    function will remember the last used setting.
    Body Trimming
    w Use this Groomer for its intended household
    use as described in this manual.
    w Before using, check foil, cutters and trimmers
    for wear or damage. If foil, cutters or trim-
    mers show signs of wear or damage, do not
    use Groomer as injury may occur. Do not use
    Groomer until foil, cutters or trimmers have
    been replaced.
    w Make sure that the Groomer is fully charged
    before you start trimming.
    wMake sure hair is clean and dry as wet hair
    tends to stick to the body.
    Take your time and do not move the Groomer
    too fast. Make smooth and gentle movements.
    1 Charge according to directions. Unplug
    groomer from outlet and remove cord.
    2 Press ON/OFF button ON to begin trimming.
    3 If the charge runs low, the battery status
    indicator will light up orange.
    4 Connect appliance plug to Groomer. A quick
    charge for 5 minutes gives you 5 minutes of
    trimming time.
    Body Trimming with Body Trimming
    Comb
    w Always use the body trimming comb when
    trimming sensitive areas.
    1 Put the trimmer on the Groomer handle
    (1) and turn clockwise (2) (fig. 2).
    2 Slide the body trimming comb into the
    guiding grooves on both sides of the handle
    (fig. 3).
    3 Press the Hair Length Setting Selector (1)
    and slide the comb to the desired setting (2)
    (fig. 4).
    The body trimming comb cuts hair to a length of
    1/8 - 15/32in / 3-12mm.
    4 The setting selected is shown on the back
    of the Groomer.
    w If you are trimming for the first time, start
    by using the comb at the maximum trimming
    length setting (15/32 in/12mm) to prevent
    accidentally trimming hairs too short. As you
    become familiar with the settings, adjust Hair
    Length Setting Selector to desired trimming
    length. Selector will ‘click’ into position at each
    setting.
    5 Turn the Groomer ON (fig. 5).
    6 To trim in the most effective way, move the
    Groomer slowly against the direction of hair
    growth (fig. 6). Make sure the surface of the
    comb always stays in contact with the skin.
    NOTE: Since all hairs do not grow in the same
    direction, you may want to try different trimming
    positions (i.e., upwards, downwards, or across).
    Practice is best for optimum results.
    w If a lot of hair has accumulated in the comb,
    remove the comb and blow and/or shake the
    hair out of the comb. You can also use the
    cleaning brush provided to remove hair from
    the comb area.
    w REMEMBER: You must reset the hair length
    setting selector back to your desired setting
    every time you replace the comb on the
    appliance.
    w The length setting is equal to the hair length
    that will remain after trimming.
    7 Turn off Groomer (fig. 5). Rinse the comb
    clean after each use.
    Body Shaving with Bodygroom
    Shaver
    w Do not use this Groomer to shave facial or
    scalp hair. The Groomer should only be used
    on skin below the neckline.
    w When shaving sensitive areas, you may feel
    some discomfort, irritation or reddening of the
    skin. This is normal as your skin needs time to
    adjust to shaving.
    w If your hair is longer than 13/32 in/10 mm,
    trim hair with the body trimming comb first
    for optimum shaving results.
    w For dry use, be certain your skin is clean and
    dry before using the Groomer.
    w For wet use, you may prepare your skin with
    lathered soap or shaving foam before using the
    Groomer.
    w Do not use the shaver if foil or cutters are
    damaged or broken as injury may occur.
    4 Rinse combs, attachments and appliance
    under warm tap water or with the supplied
    cleaning brush.
    5 Shake excess water from combs and
    attachments and allow to air dry thoroughly.
    6 Place the attachment back on the Groomer
    handle.
    Cleaning the Mini Foil Shaver
    1 Separate the top part of the mini shaver
    from its body (fig. 27).
    2 Blow and/or shake out any hair that may
    have accumulated inside the mini shaver
    (fig. 28).
    3 Clean the top part of the mini shaver under
    warm tap water (fig. 29).
    w The shaving foil is very delicate and should not
    be handled.
    w If foil becomes damaged, do not continue using
    the mini shaver. Do not apply pressure to shav-
    ing foil.
    w Do not clean the foil with the supplied brush,
    as this may cause damage.
    4 Shake excess water from mini shaver and
    allow to air dry thoroughly.
    Do not use a towel to dry the mini shaver as
    damage to the shaving foil could occur.
    Cleaning the Body Shaver
    1 Pull the shaving unit out of the body shaver
    (fig. 30).
    2 Blow and/or shake out any hair that may have
    accumulated inside the body shaver (fig. 31).
    3 Clean the body shaver and shaving unit
    under warm tap water (fig 32).
    w The shaving foil is very delicate and should not
    be handled.
    w If foil becomes damaged, do not continue
    using the body shaver. Do not apply pressure
    to shaving foil.
    w Do not clean the foil with the supplied brush,
    as this may cause damage.
    4 Shake excess water from body shaver and
    shaving unit and allow to air dry thoroughly.
    Do not use a towel to dry the shaving unit as
    damage could occur.
    Replacing the Bodygroom Shaver
    Shaving Foil Head
    w If the shaving unit is worn or damaged, do not
    continue using the Bodygroom shaver. Replace
    the shaving unit immediately.
    w It is recommended that you replace your
    shaving unit once a year.
    w A worn or damaged shaving unit should only
    be replaced with an original Philips Norelco
    shaving foil, model BG2000, which is
    available on the Philips Norelco website,
    www.philips.com/support or call
    1-800-243-3050 for assistance.
    w The foil is a precision part. Handle with care.
    1 Always switch Groomer OFF and remove
    Groomer plug from outlet before
    replacing shaving unit.
    2 Remove the shaving unit head by pulling it off
    the appliance.
    3 Place the new shaving unit head on the
    Groomer by snapping it into place.
    You will hear a “click”.
    After replacing the shaving unit head, check that
    the shaving head is firmly attached before using
    Groomer.
    This Groomer has no other user-serviceable
    parts. For assistance call 1-800-243-3050.
    Storage
    w Be sure Groomer is turned OFF. Remove cord
    from outlet and Groomer before storing in a
    safe, dry location where it will not be crushed,
    banged, or subject to damage.
    w Store the Groomer and attachments in the
    pouch to prevent damage.
    w Do not wrap cord around Groomer when
    storing.
    w Store cord in a safe location where it will not
    be cut or damaged.
    w Do not place or store Groomer where it can
    fall or be pulled into a tub or sink, water or
    other liquid while plugged in.
    A Bodygroom Shaver
    B Mini Foil Shaver
    C Nose/Ear Hair Trimmer
    D Precision Trimmer
    E Full Size Metal Guard Trimmer
    F Handle
    G On/Off Button
    H Turbo Button
    I Turbo Status Indicator
    J Battery Status Indicator
    K Storage Pouch
    L Small Appliance Plug
    M Adapter
    N Cleaning Brush
    O Body Trimming Comb
    P Beard and Moustache Comb
    Q Hair Clipping Comb
    Full 2-Year Warranty
    45-Day Money-Back Guarantee
    This symbol indicates that
    the Groomer can be used
    in the bath or shower.
    Registration
    Congratulations on your purchase and welcome
    to Philips Norelco!
    To fully benefit from the support that Philips
    Norelco offers, register your product at
    www.norelco.com/register
    Put It To The Test
    Like many new products, your Philips Norelco
    Multigroom Pro Grooming Kit may take a little
    getting used to. If you are using an electric
    Groomer for the first time, or if you’ve been
    using a different brand, take the time to acquaint
    yourself with your new Grooming Kit.
    Your Multigroom Pro Grooming Kit features
    head to toe styling with a Bodygroom shaver
    and powerful battery combined with all the
    attachments to make trimming facial hairs or hair
    clipping goof proof.
    Throw your scissors away and put your new
    Multigroom Pro Grooming Kit to the test. We
    guarantee precise, professional results or Philips
    Norelco will refund you the full purchase price as
    long as the request is received within 45 days of
    purchase.
    1
    /
    8
    -
    15
    /
    32
    in
    3-12mm
    3
    /
    64
    -
    23
    /
    32
    in
    1-18mm
    1
    /
    8
    -
    25
    /
    32
    in
    3-20mm
    A
    B
    C
    Q
    P
    O
    N
    M
    L
    D
    E
    F
    G
    H
    I
    K
    J
    16
    1
    17
    1
    2
    2
    18
    3
    1
    2
    19
    2
    1
    4
    1
    2
    20
    5
    21
    6
    22
    2
    1
    7
    1
    2
    23
    8
    24
    9
    25
    10
    26
    3 - 20
    11
    27
    2
    3 - 20
    1
    12
    28
    13
    29
    14
    30
    3 - 20
    1
    3
    2
    15
    31 32
    Assistance
    For assistance visit our website:
    www.philips.com/support
    or call toll free: 1-800-243-3050
    Online information is available 24 hours a day,
    7 days a week.
    Battery Removal
    w This Philips Norelco Groomer contains a
    rechargeable Lithium-Ion battery, which must
    be disposed of properly (fig. 33).
    w Battery may only be removed when
    Groomer is to be discarded.
    w For assistance, visit our website:
    www.philips.com/support or
    call toll free: 1-800-243-3050.
    1 Unplug electrical cord from outlet and
    Groomer before dismantling Groomer.
    2 Allow the Groomer to run until the
    battery is completely empty/depleted.
    Turn Groomer off.
    3 Remove any comb and/or attachment from
    Groomer.
    4 Check if there are any screws in the back or
    front of the appliance. If so, remove them.
    5 Remove the back and/or front panel of the
    appliance with a screwdriver. If necessary,
    also remove additional screws and/or parts
    until you see the printed circuit board with
    the rechargeable battery.
    6 If necessary, cut the wires to separate the
    printed circuit board and the rechargeable
    battery from the appliance.
    7 Do not attempt to replace battery. Insulate
    battery ends by covering with tape and
    or place battery in a small plastic bag.
    Discard Groomer.
    8 Contact your local town or city officials for
    battery disposal information or call
    1-800-8-BATTERY or www.rbrc.com for
    drop-off locations.
    Features
    ENGLISH
    Multigroom
    Pro
    33
    To Charge/Recharge
    w Fully charge Groomer before using for the first
    time or after non-use for a long period of time.
    w Charging, recharging or using Groomer at
    temperaturesbelow40˚Forhigherthan95˚F
    adversely affects lifespan of the battery.
    w If the Groomer is subjected to a major change
    in temperature, pressure or humidity, let the
    Groomer acclimatize for 30 minutes before
    using.
    1 Be certain Groomer is OFF.
    2 Connect small plug to Groomer and plug the
    adapter into any 120V AC outlet (fig. 1). Use
    only the cord provided.
    w An adaptor plug may be necessary for power
    cord usage in some foreign countries. Use an
    attachment plug adaptor of the proper
    configuration for the power outlet.
    3 It will take approximately 1 hour to fully
    charge the Groomer for a cordless trimming
    time of up to 60 minutes.
    4 The Battery Status Indicator will blink white
    to indicate the Groomer is charging.
    5 If the battery runs low (approximately 10
    minutes of grooming time left) the Battery
    Status Indicator will light up orange indicat-
    ing the Groomer needs to be (re) charged.
    6 Disconnect the cord and unplug from
    electrical outlet.
    4222 002 8405 1
    45-DAY MONEY-
    BACK GUARANTEE
    If you are not fully satisfied with your Philips Norelco
    Groomer send the product back and we’ll refund you
    the full purchase price.
    The Groomer must be shipped prepaid by
    insured mail, insurance prepaid, have the original
    sales receipt, indicating purchase price and date
    of purchase, and the money-back guarantee
    return authorization form enclosed. We cannot
    be responsible for lost mail.
    The Groomer must be postmarked no later
    than 45 days after the date of purchase. Philips
    Norelco reserves the right to verify the purchase
    price of the product and limit refunds not to
    exceed suggested retail price.
    To obtain money-back guarantee return
    authorization form, call 1-800-243-3050 for
    assistance.
    Delivery of refund check will occur 6–8 weeks AFTER
    receipt of returned product.
    Full Two-Year Warranty
    Philips Electronics North America Corporation warrants each new Philips
    Norelco product, Model QG3384 (except cutters, combs and foils)
    against defects in materials or workmanship for a period of two years
    from the date of purchase, and agrees to repair or replace any defective
    product without charge.
    IMPORTANT: This warranty does not cover damage resulting from
    accident, misuse or abuse, lack of reasonable care, the affixing of any
    attachment not provided with the product or loss of parts or subjecting
    the product to any but the specific voltage.* Use of unauthorized
    replacement parts will void this warranty.
    PHILIPS ELECTRONICS NORTH AMERICA CORPORATION
    WILL NOT PAY FOR WARRANTY SERVICE PERFORMED BY
    A NON-AUTHORIZED REPAIR SERVICE AND WILL NOT
    REIMBURSE THE CONSUMER FOR DAMAGE RESULTING FROM
    WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED
    REPAIR SERVICE.
    NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL,
    INCIDENTAL OR CONSEQUENTIAL DAMAGES.
    In order to obtain warranty service, simply go to www.philips.com/
    norelco or call 1-800-243-3050 for assistance. It is suggested that for
    your protection you return shipments of product by insured mail,
    insurance prepaid. Damage occurring during shipment is not covered by
    this warranty. NOTE: No other warranty, written or oral, is authorized
    by Philips Electronics North America Corporation. This warranty gives
    you specific legal rights, and you may also have other rights which vary
    from state to state. Some states do not allow the exclusion or limitation
    of incidental or consequential damages, so the above exclusion and
    limitations may not apply to you.
    *Read enclosed instructions carefully.
    Manufactured for:
    Philips Consumer Lifestyle
    A Division of Philips Electronics North America Corporation
    P.O. Box 10313, Stamford, CT 06904
    This symbol on the product’s nameplate means it is
    listed by Underwriters’ Laboratories, Inc.
    Norelco is a Registered Trademark of Philips Electronics
    North America Corporation.
    PHILIPS is a Registered Trademark of Koninklijke Philips N.V.
    © 2013 Philips Electronics North America Corporation. All Rights Reserved.
    QG3384
    Rechargeable Cordless
    Electric Groomer
    Always here to help you
    Question?
    Contact
    Philips
    Norelco
    Question?
    Contact
    Philips
    Norelco
    Register your product and get support at
    www.norelco.com/register

Имате ли въпрос относно Philips Norelco Multigroom 7100 QG3384?

manual_questions_numberofquestions 0

Задайте въпроса, който имате за Philips Norelco Multigroom 7100 QG3384 тук направо на други собственици на продукта. Дайте ясно и изчерпателно описание на проблема и Вашия въпрос. Колкото по–добре опишете проблема си и зададете въпроса си, толкова по–лесно другите собственици на Philips Norelco Multigroom 7100 QG3384 ще могат да Ви дадат добър отговор.

Тук вижте безплотното ръководство за Philips Norelco Multigroom 7100 QG3384. Прочетохте ли ръководството, но отговаря ли то на Вашия въпрос? Тогава задайте въпроса си на тази страница на други собственици на Philips Norelco Multigroom 7100 QG3384.

Спецификации на продукта

Марка Philips
Модел Norelco Multigroom 7100 QG3384
Продукт Тример за брада
EAN 0075020038395
Език Английски
Вид файл PDF
Съдържание на опаковката
Четка за почистване
Количество приставки 8
Производителност
Самонаточващо се острие
Ширина на ножа -мм
Брой стъпки за дължина 40
Работа на мокро и сухо
Стилове на оформяне на брада с тример Detailed styling, Long beard, Moustache, Short beard, Stubble look
Годен за пране
Дизайн
Цвят на продукта Матирана стомана
Мощност
Тип батерия Вградена
Технология на батерията Литиево-йонна (Li-Ion)
Брой поддържани батерии 1
Време на работа 60мин
Време за зареждане
AC входно напрежение 100 - 240V
Бързо зареждане
Бързо зареждане 5мин
Индикатор за нивото на батерията

Купете свързани продукти:

    Свързани продукти

    Тример за брада Philips

    manual_uploadmanual_title

    manual_uploadmanual_description