FinishVXC8/VXC6 : Black painting (approximate value: Munsell N3)
VXC8W/VXC6W : White painting (approximate value: Munsell 9.3)
Dimensions (Speaker only)Ø325 × 258.5D mm (Ø12-13/16" × 10-3/16"D)Ø286 × 204D mm (Ø11-1/4" × 8-1/16"D)
Net weight (Speaker only, 1 piece)6.6 kg (14.6 lbs)4.4 kg (9.7 lbs)
Cutout sizeØ285 mm (Ø11-1/4")Ø247 mm (Ø9-3/4")
Required ceiling board thickness5 mm – 35 mm *
Conduit tubeup to 1/2"
PackagingPackaged in pair
INSTALLING THE SPEAKERS
Install the speakers onto the ceiling with the supplied hardware. Ensure that
the strength of the ceiling rail is sufficiently strong.
Illustrations in this manual are for the VXC6. The installation method is the
same for other models.
Pre-installation (Preparation of the Cable)
Use stranded wire for cables attached to the Euroblock connector. Strip
their insulation as shown in the figure and connect them.
Do not plate stranded wires by solder. Doing so will cause the wire to break.
1Put the supplied cutout template to the ceiling and draw a circle by
Make sure to use the cutout template so that hole is the correct
If you use a circular cutter, set the diameter with the cutout template.
2Cut the hole by tracing the circle.
Be careful to prevent chips or powder entering your eyes while
cutting the hole.
1Insert the two tile rails through the cut hole and place them on the
ceiling surface within your reach. Be sure that each tile rails are
oriented as shown below.
2Insert the folded O-ring through the cut hole and open it in the ceiling.
3Secure the O-ring and tile rails with supplied two screws through
either slot of both O-ring brackets.
1Pull the wiring from the amplifier through the cut hole.
2Loosen the screw at the right of the terminal cover to open the
terminal cover and remove the Euroblock connector.
3After loosening the terminal screws of the Euroblock connector with a
flat-blade screwdriver, insert the cable into each terminal and tighten
the screws. Make sure that cables cannot be pulled out.
Use a flat-blade screwdriver with a blade less than 3 mm (0.1 in.).
CUT OUT A HOLE IN THE CEILING
INSTALL THE TILE RAILS AND O-RING
CONNECT THE WIRING TO THE CONNECTOR AND FIX
About 7 mm (0.3 in.)
Less than 3 mm (0.1 in.)
There are two acceptable wiring methods.
When connecting with low impedance, take note of the combined
Using Loop-Through Terminals
For this method, cables are connected from terminals 1 and 4 to the
subsequent speaker. If the Euroblock connector is disconnected from
a speaker, all subsequent speakers will not work. This can be useful
to identify which speaker has a problem.
Paralleling Input Terminals
For this method, cables are connected to terminals 2 and 3 of each
speaker. Since the cables are connected via Euroblock connectors,
subsequent speakers can work even if a problem occurs with a
4Plug the connected Euroblock connector into the socket in the
5Loosen the screw A of the strain relief clamp.
6Remove the screw B of the strain relief clamp.
If the cable is not to be held, remove the screw A and remove the
strain relief fitting, then proceed to step 8.
From amplifier or
From amplifier or
7Hold the cable in the strain relief clamp, then tighten screws A and B.
8Close the terminal cover and tighten the screw.
1Attach the safety wire to the safety wire ring, and connect the wire to
an independent support point, such as a joist.
Always take measures to prevent the speaker from falling down.
If the safety wire is too short, prepare another wire appropriate for the
speaker weight and installation conditions. If the wire is too long,
should the speaker fall, the wire may snap as a result of too much
2Push up the speaker slowly into the ceiling, taking care not to trap the
FIX THE SPEAKERS ONTO THE CEILING
Safety wire ring
When all the Anti-Drop Tabs cross
over the O-ring, the speaker is held
To release the speaker from the
O-ring, press the Anti-Drop Tabs.
These are located above the U
mark near the edge of the baffle’s
3Turn the screwdriver a half turn counterclockwise to loosen the
attachment screw (located beside the U mark). This makes the
clamp easier to align in the channel.
4Turn the screwdriver clockwise to tighten the attachment screw.
The first turn of the attachment screw aligns the clamp with the
channel. Further turns move the clamp down the channel to pull the
speaker up into the ceiling.
•Do not over-tighten the attachment screw. Otherwise, the
attachment screw and clamp will break.
•Do not turn any screws other than attachment screw (located
beside the U mark). Otherwise, the speaker may fall or
Select the line voltage/impedance (100V/70V/8Ω) and power tap for 100V/
70V line distributed system, by rotating the tap selector switch on the front
side of the speaker with a flat-blade screwdriver.
•The “X” position should not be selected. The 8Ω position should be
selected for 8Ω audio systems only. If the setting is incorrect, it may
cause malfunction of the speaker and amplifier.
•Make sure the amplifier is switched off before operating the tap selector
Fit the grille to the baffle front and turn it clockwise.
The grille may fall down if it is attached inadequately. Attach it firmly.
SET THE LINE VOLTAGE/IMPEDANCE AND POWER
ATTACH THE GRILLE
Illustration indicates the setting at 60 W for 100 V
line and 30 W for 70 V line.
Имате ли въпрос относно Yamaha VXC8?
Брой въпроси: 0
Задайте въпроса, който имате за Yamaha VXC8 тук направо на други собственици на продукта. Дайте ясно и изчерпателно описание на проблема и Вашия въпрос. Колкото по–добре опишете проблема си и зададете въпроса си, толкова по–лесно другите собственици на Yamaha VXC8 ще могат да Ви дадат добър отговор.
Относно Yamaha VXC8
Тук вижте безплотното ръководство за Yamaha VXC8. Прочетохте ли ръководството, но отговаря ли то на Вашия въпрос? Тогава задайте въпроса си на тази страница на други собственици на Yamaha VXC8. Задайте въпроса си тук