Yamaha VXS10S

Yamaha VXS10S ръководство на потребителя

    * Please keep this manual in a safe place for future reference.
    Always follow the basic precautions listed below to avoid the possibility of
    serious injury or even death from electrical shock, short-circuiting, damages,
    fire or other hazards. These precautions include, but are not limited to, the
    This device contains no user-serviceable parts. Do not open the device or attempt
    to disassemble the internal parts or modify them in any way. If it should appear to
    be malfunctioning, discontinue use immediately and have it inspected by qualified
    Yamaha service personnel.
    Do not expose the device to rain, use it near water or in damp or wet conditions, or
    place on it any containers (such as vases, bottles or glasses) containing liquids
    which might spill into any openings. If any liquid such as water seeps into the
    device, have the device inspected by qualified Yamaha service personnel.
    Always follow the basic precautions listed below to avoid the possibility of
    physical injury to you or others, or damage to the device or other property.
    These precautions include, but are not limited to, the following:
    Do not place the device in an unstable position where it might accidentally fall over.
    Do not place the device in a location where it may come into contact with corrosive
    gases or salt air. Doing so may result in malfunction.
    Construction work should be carried out in accordance with construction-related
    law and always by a professional constructor. If the device installation requires
    construction work, make sure to observe the following precautions.
    - Choose mounting hardware and an installation location that can support the
    weight of the device.
    - Avoid locations that are exposed to constant vibration.
    - Use the required tools to install the device.
    - Inspect the device periodically.
    When transporting or moving the device, always use two or more people.
    Attempting to lift the device by yourself may damage your back, result in other
    injury, or cause damage to the device itself.
    Before connecting the device to a power amplifier, turn off the power for all devices.
    Before turning the power on or off for all devices, set all volume levels to minimum.
    Use only speaker cables for connecting speakers to the speaker connectors. Use of
    other types of cables may result in fire.
    Do not wipe the outer packaging with benzine, thinner, or synthetic detergent and
    do not use electrical contact cleaner. These may damage the outer packaging and
    dissolve the parts.
    Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into holes of
    the grille. If this happens, have the device inspected by qualified Yamaha service
    Do not operate the device if the sound is distorting. Prolonged use in this condition
    could cause overheating and result in fire.
    When choosing a power amplifier for use with this device, make sure that the output
    power of the amplifier is lower than the power capacity of this device (see
    Even if the output power of the amplifier is lower than the power capacity of this
    device (PGM), use of excessive input signals resulting in clipping may cause
    damage to the device.
    Malfunction or fire may occur especially when the following sounds or noises are
    - feedback, when using a microphone
    - continuous and extreme volume sound from a musical instrument
    - extreme continuous distorted sound
    - noise caused by plugging/unplugging the cable while the amplifier is turned on
    Do not open
    Water warning
    Handling caution
    To avoid the possibility of malfunction/damage to the product or damage to other
    property, follow the notices below.
    ƔHandling and Maintenance
    Do not place vinyl, plastic or rubber objects on the device, since this might discolor
    the cabinet.
    When cleaning the device, use a dry and soft cloth. Do not use paint thinners,
    solvents, cleaning fluids, or chemical-impregnated wiping cloths.
    Condensation can occur in the device due to rapid, drastic changes in ambient
    temperature-when the device is moved from one location to another, or air
    conditioning is turned on or off, for example. Using the device while condensation is
    present can cause damage. If there is reason to believe that condensation might
    have occurred, leave the device for several hours until the condensation has
    completely dried out.
    Be sure to observe the amplifier’s rated load impedance (see SPECIFICATIONS),
    particularly when connecting speakers in parallel. Connecting an impedance load
    outside the amplifier’s rated range can damage the amplifier.
    When connecting the speakers with high impedance, be sure that the output total of
    each speaker does not exceed the rated output of the power amplifier.
    This speaker system has an internal protection circuit that shuts off the speaker unit
    when an excessive input signal is applied.
    If the speaker unit emits no sound, reduce the volume level of the amplifier
    The sound will return automatically in several seconds.
    Place the speaker on a flat and smooth surface.
    ƔAbout This Manual
    The illustrations as shown in this manual are for instructional purposes only, and may
    appear somewhat different from those on your device.
    Yamaha cannot be held responsible for damage caused by improper use or
    modifications to the device.
    Information for Users on Collection and Disposal of Old Equipment
    This symbol on the products, packaging, and/or accompanying
    documents means that used electrical and electronic products
    should not be mixed with general household waste.
    For proper treatment, recovery and recycling of old products, please
    take them to applicable collection points, in accordance with your
    national legislation and the Directives 2002/96/EC.
    By disposing of these products correctly, you will help to save
    valuable resources and prevent any potential negative effects on
    human health and the environment which could otherwise arise from inappropriate
    waste handling.
    For more information about collection and recycling of old products, please contact
    your local municipality, your waste disposal service or the point of sale where you
    purchased the items.
    [For business users in the European Union]
    If you wish to discard electrical and electronic equipment, please contact your dealer
    or supplier for further information.
    [Information on Disposal in other Countries outside the European Union]
    This symbol is only valid in the European Union. If you wish to discard these items,
    please contact your local authorities or dealer and ask for the correct method of
    Unpack the contents and confirm that all the following items are included.
    Speaker × 1
    Bracket base × 1
    Mounting bracket × 1
    Captive washer screw × 4
    Rubber spacer × 4 (14 mm thickness)
    Hexagon bolt × 4
    Spring washer × 4
    Flat washer × 4
    Safety wire × 1
    Owner’s Manual (this manual)
    * Screws/bolts to fasten the bracket onto the wall and speaker cables are not included.
    *1: Half-space (2π)
    *2: Calculated based on power rating and sensitivity, exclusive of power compression.
    *3: Impedance lower limit (per satellite output) VXS10S/VXS10SW: 4 Ω, VXS10ST/VXS10STW: 8 Ω
    The contents of this manual apply to the latest specifications as of the printing date. Since Yamaha makes continuous improvements to the product, this manual
    may not apply to the specifications of your particular product. To obtain the latest manual, access the Yamaha website then download the manual file. Since
    specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.
    The dimensions are shown overleaf.
    Type Subwoofer, Bass reflex
    Component 10" (25 cm) Cone driver, Dual voice coil
    Nominal impedance 8 Ω + 8 Ω
    Power rating NOISE 100 W + 100 W
    PGM 200 W + 200 W
    MAX 400 W + 400 W
    Sensitivity (1W, 1m) *
    96 dB SPL 96 dB SPL
    Maximum SPL (Calculated, 1m) *
    125 dB SPL
    Frequency range (-10 dB) *
    45 Hz – 250 Hz 45 Hz – 250 Hz
    Subwoofer filter Network: Low-pass filter 6 dB/Oct, 200 Hz
    Acoustic filter: Low-pass filter 6 dB/Oct, 200 Hz
    Satellite filter Network: High-pass filter 6 dB/Oct, 200 Hz
    Satellite impedance 8 Ω load per satellite output recommended *
    Connector Euroblock (4 pin) × 1:
    Input (CH1: +/-, CH2: +/-)
    Euroblock (4 pin) × 1:
    Input (input: +/-, loop-thru: +/-)
    Euroblock (4 pin) × 1: Satellite output (ST1: +/-, ST2: +/-)
    Euroblock (5 pin) × 1: transformer taps
    Transformer taps 70 V 200 W, 100 W, 50 W, 25 W
    100 V 200 W, 100 W, 50 W
    Overload protection Full-range power limiting to protect network and transducers
    Magnetically shielded No
    Enclosure Shape Rectangle
    Cabinet material MDF
    Finish VXS10S/VXS10ST: Black (PVC, approximate value: Munsell N3)
    VXS10SW/VXS10STW: White (PVC, approximate value: Munsell 3.5PB9.0/1)
    Dimensions (Speaker only) 260 × 500 × 389 mm (10.2" × 19.7" × 15.3")
    Net weight (Speaker only) 16.5 kg (36.4 lb) 19.5 kg (43.0 lb)
    When installing the speaker on the floor, attach the rubber spacers to the
    underside of the speaker to provide support. Affix the rubber spacers firmly
    when you attach them.
    When installing the speaker on a wall or ceiling, use the included brackets
    or optional U-bracket UB-DXR8. Ensure that the wall/ceiling is sufficiently
    This package does not include the mounting hardware to install the
    included brackets/safety wire or the UB-DXR8. If you are not sure what
    materials are required for installation, consult a specialist.
    An installed speaker is shown below. Install the bracket as shown.
    Do not use the included brackets for ceiling installation.
    Do not use the UB-DXR8 for wall installation.
    Pre-installation (Preparation of the cable)
    Use stranded wire for cables attached to the Euroblock connector. Strip
    their insulation as shown in the figure and connect them.
    Do not plate stranded wires by solder. Doing so will cause the wire to break.
    Connect the cable from the amplifier to the “INPUT” socket, and the cable
    being connected to other speakers to the “SATELLITE SPEAKERS”
    A signal input to CH1 of INPUT is output from ST1 of SATELLITE
    SPEAKERS, and signal input to CH2 of INPUT is output from ST2 of
    For VXS10ST/VXS10STW, connect the included 5-pin Euroblock
    connector as shown below and set the appropriate wattage when using
    100 V/70 V line.
    No setting should be made for 100 V line, as shown in the far left illustration.
    1 Remove the Euroblock connector from the speaker.
    Wall installation
    (using included brackets)
    Ceiling installation
    (using optional bracket
    About 7 mm (0.3 in.)
    2 After loosening the terminal screws of the Euroblock connector with a
    flat-blade screwdriver, insert the cable into each terminal and tighten
    the screws. Make sure that cables cannot be pulled out.
    Use a flat-blade screwdriver with a blade less than 3 mm (0.1 in.).
    3 (VXS10ST/VXS10STW only) Plug the 5-pin Euroblock connector into
    1 Place the bracket base on the wall and
    mark the position for screws/bolts. The
    diameter of seven holes for screw/bolt
    (not included) is ø6.5 mm.
    2 Make holes in the wall for the bolts, as
    required, and feed the bolts through
    the holes.
    3 Affix the bracket base on the wall. The
    narrow edge of the bracket base
    should be oriented downward.
    4 Attach the mounting bracket to the speaker with the included screws
    with captive washer.
    The narrow edge of the mounting bracket should be oriented
    5 Attach the two rubber spacers to the bottom edge of the speaker.
    Make sure the spacers are located near the outer edge; otherwise,
    they will impede installation on the bracket base in the next step.
    Affix the rubber spacers firmly when you attach them.
    6 Slide the speaker down onto the bracket base until it locks in place.
    Be sure to perform this work with two or more people.
    Installing on the wall (using the included brackets)
    Euroblock connector
    Less than 3 mm (0.1 in.)
    Bracket base
    Mounting bracket
    Captive washer screw
    Rubber spacer
    To detach the mounting bracket from the bracket base, release the
    lock of the mounting bracket with a long flat-blade driver and lift the
    Be sure to perform this work with two or more people.
    7 Plug the Euroblock connectors into the
    To determine the appropriate size of the UB-DXR8, download the “U
    BRACKET OWNER’S MANUAL” from the following manual library site.
    1 Assemble two L-shaped brackets into a U-shape using the M5 × 10
    screws included with the UB-DXR8 as shown below. Peel off the
    sheet from each rubber spacer (14 mm thickness; included with the
    speaker), and attach the spacers to the inside of each bracket arm
    aligning the holes so that the hexagon bolts can be inserted.
    Affix the rubber spacers firmly when you attach them.
    2 Make sure that the width of the U bracket matches the speaker width.
    3 Affix the U bracket on the ceiling using appropriate mounting
    4 Use the hexagon bolts, spring washers and flat washers included
    with the speaker to attach the speaker to the UB-DXR8.
    Be sure to perform this work with two or more people.
    Installing on the ceiling (using the optional UB-DXR8)
    M5 × 10
    Rubber spacer
    Hexagon bolt
    Spring washer
    Flat washer
    5 Plug the Euroblock connectors into the
    This section explains how to attach the included safety wire.
    Make sure to take measures to prevent the speaker from falling down in
    the event of a installation failure.
    When installing the safety wire to the wall, install it higher than the wire’s
    attachment point on the speaker, with as little slack as possible.
    If the safety wire is too short, prepare another wire appropriate for the
    speaker weight and installation conditions. If the wire is too long, should
    the speaker fall, the wire may snap as a result of too much strain.
    1 Pass the safety wire through the eyebolt on the rear of the speaker.
    2 Pass the bracket of the safety wire through the loop on the other end,
    and pull tight up against the eyebolt.
    3 Affix the bracket of the safety wire to the wall.
    Owner’s Manual
    Surface Mount Speaker
Yamaha VXS10S

Имате ли въпрос относно Yamaha VXS10S?

Брой въпроси: 0

Задайте въпроса, който имате за Yamaha VXS10S тук направо на други собственици на продукта. Дайте ясно и изчерпателно описание на проблема и Вашия въпрос. Колкото по–добре опишете проблема си и зададете въпроса си, толкова по–лесно другите собственици на Yamaha VXS10S ще могат да Ви дадат добър отговор.

Тук вижте безплотното ръководство за Yamaha VXS10S. Прочетохте ли ръководството, но отговаря ли то на Вашия въпрос? Тогава задайте въпроса си на тази страница на други собственици на Yamaha VXS10S. Задайте въпроса си тук

Спецификации на продукта

Марка Yamaha
Модел VXS10S
Продукт Тонколона
EAN 4957812531276, 0086792974095
Език Английски
Вид файл PDF
Тип субуфер -
RMS мощност на субуфера 100W
Честотен обхват на субуфера 45 - 250Hz
Чувствителност на субуфера 96dB
Диаметър на драйвера на субуфера (имперски единици) 10 2011-05-04 11:27:54 2012-06-08 13:40:02 3166 16 22
Цвят на продукта Черен
Материал MDF
Тегло и размери
Ширина на субуфера 260мм
Дълбочина на субуфера 389мм
Височина на субуфера 500мм
Тегло на субуфера 16500г

Свързани продукти

Тонколона Yamaha